Network Appliance NS0-183 Dumps - The Sure Way To Pass Exam
NS0-183 Exam Questions (Updated 2022) 100% Real Question Answers
NEW QUESTION 22
What are two ONTAP storage efficiency technologies that would be used on an AFF A400 cluster? (Choose two.)
- A. FlexClone volumes
- B. Flash Pool
- C. FlashCache
- D. thin provisioning
Answer: A,D
Explanation:
https://docs.netapp.com/ontap-9/index.jsp?topic=%2Fcom.netapp.doc.dot-cm-concepts%2FGUID-8A8108CF-499A-46FC-917F-A40FAD68C8D6.html
NEW QUESTION 23
You just installed a new AFF A220 2-node cluster without additional disk shelves. When you review the Config Advisor output, you notice that your SAS cabling appears to be single-path HA.
In this scenario, which statement is true?
- A. Cable controller 1 0a to controller 2 0b, and cable controller 1 0b to controller 2 0a.
- B. Cable controller 1 0a to controller 2 0a, and cable controller 1 0b to controller 2 0b.
- C. AFF A220 controllers with internal disks support only single-path HA.
- D. The Config Advisor version you are using requires a plugin for AFF controllers.
Answer: A
NEW QUESTION 24
Which statement regarding Epsilon is true?
- A. The node holding the epsilon has extra fractional vote weight.
- B. Epsilon is reassigned automatically to the HA partner in case the current owner of the epsilon suddenly reboots.
- C. Whenever a new node is added, the epsilon is automatically reassigned to this node.
- D. The epsilon acts as a tiebreaker in a 2-node cluster.
Answer: A
NEW QUESTION 25
Click the Exhibit button.
Your ONTAP cluster shows the cluster network errors that are shown in the event log.
What is used by ONTAP software to log the errors that are shown in the exhibit?
- A. BGP
- B. EMS
- C. AutoSupport
- D. SNMP
Answer: B
NEW QUESTION 26
Node 3 has taken over Node 4. You are attempting to access Node 4 on its management interface but cannot do it. In this scenario, how would you access Node 4's management interface?
- A. You should use SSH directly to one of the cluster interconnect switches; from there, you can use SSH to the node management on node 4.
- B. You have not waited long enough for the failover timeout for a node management LIF; there is a broadcast domain configured for this situation.
- C. Connect to the node management on Node 3 and then use the HA interconnect to access node 4.
- D. You must use the Service Processor; node management LIFS do not fall over between nodes.
Answer: D
NEW QUESTION 27
You have a 6-node ONTAP 9.1 cluster with two FAS6290 nodes and four FAS8080 EX nodes using a SAN protocol.
In this scenario, how many FAS9000 HA pairs would be joined to this cluster?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
NEW QUESTION 28
Which statement is true about cluster interconnect?
- A. It is needed for the replication network between clusters.
- B. It is a management network for cluster administration and can be used for interconnect LIFs.
- C. It transports the data between nodes if a Data LIF has a non-optimized path.
- D. It provides the core data network communication.
Answer: C
NEW QUESTION 29
You are installing a new ONTAP 9.7 cluster and attaching the cluster to two separate networks. Your customer has indicated that the same range of client IP addresses are used on both networks and that the networks are never allowed to communicate with each other.
In this scenario, which ONTAP feature must be configured to securely allow all clients to access ONTAP NAS protocols?
- A. BGP
- B. IPspaces
- C. routing
- D. broadcast domains
Answer: B
NEW QUESTION 30
You want to ensure the highest path resilience and performance increase to the storage stack on your FAS8700 cluster.
In this scenario, which two types of stack cabling are available to use? (Choose two.)
- A. mixed-mode
- B. multipath HA
- C. quadpath HA
- D. single path
Answer: A,B
NEW QUESTION 31
You configured AutoSupport and are trying to send a full AutoSupport message to NetApp.
You use the autosupport history showcommand and see the output shown in the exhibit.
The customer confirms that the AutoSupport settings are correct.
Which two actions will solve this issue? (Choose two.)
- A. The customer needs to enable AutoSupport for both nodes.
- B. The customer needs to change the transport protocol to HTTP.
- C. The customer needs to white-list the two nodes on their mail server.
- D. The customer needs to exclude the two nodes from the attachment-size limitation.
Answer: A,C
NEW QUESTION 32
Click the Exhibit button.
You want to add a FAS2750 HA pair to an existing 6-node cluster.
Referring to the exhibit, which action would you perform to begin adding the node?
- A. Use the exit or quit commands then run the cluster setup command.
- B. Use the node setup wizard and select 0a as the management interface.
- C. Reboot the node and enter maintenance mode and run the Cluster Setup wizard.
- D. Use the back command to begin the Cluster Setup wizard.
Answer: A
Explanation:
https://docs.netapp.com/ontap-9/index.jsp?topic=%2Fcom.netapp.doc.dot-cm-sag%2FGUID-B13FF812-785E-4E62-9914-30E7A8F51A4C.html
NEW QUESTION 33
You are setting up a new AFF A400 that will serve iSCSI LUNs. You will have four iSCSI SVMs that each need to connect to an Internet Storage Name Service (iSNS) for discovery and management purposes.
In this scenario, which network interface is needed for each SVM to register with the name service?
- A. intercluster LIF
- B. SVM management LIF
- C. node management LIF
- D. SVM data LIF
Answer: A
NEW QUESTION 34
You need to install a cluster with a FAS2720 HA pair and a FAS8300 HA pair.
Which NetApp tool will verify which cluster interconnect switches support this configuration?
- A. Interoperability Matrix Tool (IMT)
- B. mysupport.netapp.com site
- C. Hardware Universe (HWU)
- D. Active IQ Config Advisor
Answer: C
NEW QUESTION 35
Which LIF type is used by default for hardware-assisted storage failover communication?
- A. data
- B. intercluster
- C. node-mgmt
- D. cluster-mgmt
Answer: C
NEW QUESTION 36
You completed an ONTAP cluster deployment as a reseller engineer. During the knowledge transfer process to the customer, they ask for proof that the array has correct multi-path HA cabling deployed and that the array is error free.
Which documentation output would you present to the customer to satisfy this requirement?
- A. Active IQ Unified Manager output
- B. NetAppDocs output
- C. Config Advisor output
- D. Active IQ OneCollect output
Answer: C
Explanation:
Explanation/Reference: https://docs.netapp.com/platstor/topic/com.netapp.doc.hw-controller-add/GUID-64A51339-
1F03-451C-B062-9F97E772817E.html
NEW QUESTION 37
After completing the installation of a DS224C shelf, you observe the error shown in the exhibit.
Which action should you take to troubleshoot the error? (Choose two.)
- A. Perform a takeover-giveback.
- B. Re-seat the SAS card.
- C. Re-seat the IOM module.
- D. Reconnect the SAS cable.
Answer: C,D
NEW QUESTION 38
Click the Exhibit button.
Your ONTAP cluster shows the cluster network errors that are shown in the event log. What is used by ONTAP software to log the errors that are shown in the exhibit?
- A. BGP
- B. EMS
- C. AutoSupport
- D. SNMP
Answer: B
NEW QUESTION 39
A 4-node cluster has connectivity for both block and file access. Nodes 1 and 3 are used for file access, and nodes 2 and 4 are used for block access. During routine maintenance, node 4 is switched off and the LIFs are migrated to other nodes. Upon investigation, you see that the LIFs that serve file traffic have moved to alternative ports.
However, LIFs that serve the block have not migrated. In this scenario, what is happening?
- A. There is a faulty SFP.
- B. The failover group is configured incorrectly.
- C. The fiber switch is configured incorrectly.
- D. The LIFs that serve the block protocol do not failover.
Answer: D
NEW QUESTION 40
......
Pass Network Appliance NS0-183 Exam Quickly With ExamCost: https://pass4sure.examcost.com/NS0-183-practice-exam.html
