[2026] Practice with these NS0-014 dumps Certification Sample Questions
Get Instant Access of 100% REAL NS0-014 DUMP Pass Your Exam Easily
NEW QUESTION # 59
When transitioning from FC to IP MetroCluster, which two components must be replaced? (Select two)
- A. Ethernet switches
- B. Fibre Channel switches
- C. Mediator software
- D. ATTO FibreBridges
Answer: B,D
NEW QUESTION # 60
What technology does NetApp MetroCluster use to ensure zero data loss during failover?
- A. Asynchronous replication
- B. Deduplication
- C. Synchronous replication
- D. Snapshot
Answer: C
NEW QUESTION # 61
What factors should be considered when planning for the deployment of MetroCluster FC configurations? (Select two)
- A. IP connectivity
- B. Availability of ATTO bridges
- C. Number of Ethernet ports
- D. Support for Fibre Channel
Answer: B,D
NEW QUESTION # 62
What is a key advantage of IP MetroCluster over Fibre Channel MetroCluster?
- A. Increased storage capacity
- B. Easier setup and longer distance replication
- C. Higher performance
- D. Lower bandwidth requirements
Answer: B
NEW QUESTION # 63
Which tool is commonly used to assess MetroCluster prerequisites before installation?
- A. OnCommand System Manager
- B. StorageGRID
- C. Active IQ Unified Manager
- D. Config Advisor
Answer: D
NEW QUESTION # 64
When implementing a MetroCluster solution, which two actions ensure data integrity and availability? (Select two)
- A. Using Snapshot copies for data backup
- B. Regularly testing failover procedures
- C. Configuring SyncMirror for all volumes
- D. Enabling deduplication on all volumes
Answer: B,C
NEW QUESTION # 65
During a MetroCluster installation, which component is responsible for ensuring automatic failover in the event of a site failure?
- A. ONTAP Mediator
- B. SnapVault
- C. ATTO FibreBridge
- D. SyncMirror
Answer: A
NEW QUESTION # 66
When upgrading MetroCluster hardware, which two actions should be taken to minimize downtime? (Select two)
- A. Schedule the upgrade during peak usage hours
- B. Validate all hardware components with the Interoperability Matrix Tool (IMT)
- C. Avoid testing the configuration post-upgrade
- D. Use Non-Disruptive Upgrade (NDU) for ONTAP upgrades
Answer: B,D
NEW QUESTION # 67
During an IP MetroCluster failover test, which key component ensures the consistency of replicated data?
- A. ATTO Bridge
- B. FC Switch
- C. SnapMirror
- D. Mediator
Answer: D
NEW QUESTION # 68
What are two critical elements of the physical layer in an FC MetroCluster configuration? (Select two)
- A. ATTO FibreBridge
- B. Mediator server
- C. Ethernet switches
- D. FC switches
Answer: A,D
NEW QUESTION # 69
Which of the following is a major advantage of using IP MetroCluster over FC MetroCluster?
- A. Reduced need for FC switches
- B. Easier to deploy over long distances
- C. Increased data redundancy
- D. Lower bandwidth requirements
Answer: B
NEW QUESTION # 70
What does the MetroCluster Tiebreaker monitor to determine if a failover should occur?
- A. Site availability
- B. Inter-site latency
- C. Mediator heartbeat
- D. Data replication status
Answer: A
NEW QUESTION # 71
What are two benefits of transitioning from an FC-based MetroCluster to an IP-based MetroCluster? (Select two)
- A. Lower hardware costs due to fewer FC components
- B. Easier long-distance replication
- C. Faster sync replication
- D. Increased storage capacity
Answer: A,B
NEW QUESTION # 72
Which MetroCluster components require configuration for both FC and IP configurations? (Select two)
- A. Tiebreaker software
- B. IP switches
- C. ATTO bridges
- D. WAN connections
Answer: A,D
NEW QUESTION # 73
What are two key considerations when deploying a MetroCluster solution? (Select two)
- A. Distance between MetroCluster sites
- B. Type of storage media used
- C. Whether deduplication is enabled
- D. Bandwidth availability for inter-site communication
Answer: A,D
NEW QUESTION # 74
Which component is responsible for managing site failover in an IP-based MetroCluster?
- A. ONTAP Mediator
- B. ATTO FibreBridge
- C. SyncMirror
- D. SnapMirror
Answer: A
NEW QUESTION # 75
Which two configuration steps are essential when installing MetroCluster Tiebreaker software?
(Select two)
- A. Install ONTAP Mediator
- B. Enable SyncMirror
- C. Set up IP connectivity between clusters
- D. Configure cross-site LIFs
Answer: C,D
NEW QUESTION # 76
Which protocol is primarily used for data replication between MetroCluster sites in an IP-based configuration?
- A. FCoE
- B. Fibre Channel
- C. IP
- D. iSCSI
Answer: C
NEW QUESTION # 77
What are the two types of MetroCluster configurations available? (Select two)
- A. IP MetroCluster
- B. Ethernet MetroCluster
- C. MPLS MetroCluster
- D. FC MetroCluster
Answer: A,D
NEW QUESTION # 78
Which command is used to verify the health of a MetroCluster configuration in ONTAP?
- A. metrocluster diagnostic show
- B. cluster status
- C. metrocluster show
- D. metrocluster check connectivity
Answer: C
NEW QUESTION # 79
......
Free Exam Files Downloaded Instantly: https://pass4sure.examcost.com/NS0-014-practice-exam.html
