[2024] Free HPE2-W09 Exam Dumps to Pass Exam Easily
HPE2-W09 Exam Dumps, HPE2-W09 Practice Test Questions
NEW QUESTION # 17
Is this part of the process for using NetEdit to update firmware on ArubaOS-CX switches?
Solution: Use a firmware update plan to manage both updating the Image on selected devices and reboot.
- A. No
- B. Yes
Answer: A
NEW QUESTION # 18
Is this a way that Virtual Switching Extension (VSX) differs from Virtual Switching Framework (VSF)?
Solution: VSX permits admins to select which features to synchronize between members while VSF requires manual configuration of Identical features on each member of the VSF fabric.
- A. Yes
- B. No
Answer: A
Explanation:
VSX permits admins to select which features to synchronize between members while VSF requires manual configuration of identical features on each member of the VSF fabric is a way that Virtual Switching Extension (VSX) differs from Virtual Switching Framework (VSF). VSX is a feature that provides active-active forwarding and redundancy for ArubaOS-CX switches. VSF is a feature that provides active-standby forwarding and redundancy for legacy campus switches.
VSX allows admins to select which features to synchronize between members using an opt-in model, while VSF requires manual configuration of identical features on each member using a commander-member model.
NEW QUESTION # 19
Is this a use case for deploying Ethernet Ring Protection Switching (ERPS)?
Solution: connecting multiple data centers at Layer 2 while minimizing the number of dark fiber connections required
- A. No
- B. Yes
Answer: A
NEW QUESTION # 20
Does this correctly describe NetEdit's notification capabilities?
Solution: NetEdit notifies admins of errors using Its Internal email server.
- A. No
- B. Yes
Answer: A
NEW QUESTION # 21
You enter this command on an ArubaOS-CX switch:
Switch# show erps status ring 1
Is this what the specified status means?
Solution: The status is Idle, which means that the ring is up and fully connected with the RPL port blocked.
- A. No
- B. Yes
Answer: A
Explanation:
The status is Idle, which means that the ring is up and fully connected with the RPL port blocked is not what the specified status means for Ethernet Ring Protection Switching (ERPS) on an ArubaOS-CX switch. Idle is one of the possible statuses for an ERPS ring instance, but it indicates that the ring is not operational and no port is blocked. This can happen when the ring is not configured properly or when there is a miscommunication between the nodes1.
NEW QUESTION # 22
A customer's servers use ISCSI, and they send data and storage traffic on the same pair of I OGbE links. Is this a best practice for supporting the ISCSI requirements?
Solution: Set up dedicated switches to connect to iSCSl arrays. Connect top of rack (ToR) switches, which will support both data and storage traffic, to those dedicated switches.
- A. Yes
- B. No
Answer: A
Explanation:
Setting up dedicated switches to connect to iSCSI arrays and connecting top of rack (ToR) switches, which will support both data and storage traffic, to those dedicated switches is a best practice for supporting the iSCSI requirements. This provides isolation and security for the iSCSI traffic and reduces the risk of congestion or latency on the storage network.
NEW QUESTION # 23
Does this correctly describe the ArubaOS-CX architecture?
Solution: The AtubaOS-CX software is based on the ArubaOS-Switch software and adds data center features.
- A. No
- B. Yes
Answer: A
Explanation:
The ArubaOS-CX software is based on the ArubaOS-Switch software and adds data center features is not a correct description of the ArubaOS-CX architecture. The ArubaOS-CX software is a new operating system that is designed for data center and campus networks. It is not based on the ArubaOS-Switch software, which is used for legacy campus switches. The ArubaOS-CX software provides advanced features such as VSX, EVPN, NAE, REST APIs, etc.
NEW QUESTION # 24
Is this a way that Virtual Switching Extension (VSX) differs from Virtual Switching Framework (VSF)?
Solution: VSX features a dual control plane while VSF features a single control plane.
- A. Yes
- B. No
Answer: A
Explanation:
VSX features a dual control plane while VSF features a single control plane. VSX and VSF are both high availability solutions that provide redundancy and load balancing across a pair of switches. However, VSX features a dual control plane, which means that each switch has its own independent configuration and state information. VSF features a single control plane, which means that one switch acts as the commander and synchronizes the configuration and state information to the other switch. The statement is true because it correctly describes the difference between VSX and VSF control planes.
NEW QUESTION # 25
You are using NetEdit to manage AruDaOS-CX switches. You want to deploy a standard config to the switches, but need the config to include a few device-specific settings such as hostname and IP address.
Is this what you should do?
Solution: omit the device-specific settings from the configuration plan and include them in command scripts instead.
- A. No
- B. Yes
Answer: A
Explanation:
Omit the device-specific settings from the configuration plan and include them in command scripts instead is not what you should do if you want to use NetEdit to manage ArubaOS-CX switches and deploy a standard config to the switches, but need the config to include a few device-specific settings such as hostname and IP address. This approach would require you to create separate command scripts for each switch, which can be tedious and error-prone. A better approach would be to use an auto config plan that uses scripts to customize the configuration for each switch based on variables such as serial number, MAC address, or user-defined parameters1.
NEW QUESTION # 26
You are configuring Ethernet Ring Protection Switching (ERPS) on an ArubaOS-CX switch. Is this a guideline for configuring timers?
Solution: The hold off timer causes ERPS switches to delay unblocking a failed link after the link is restored. This can be useful to prevent frequent topology changes.
- A. Yes
- B. No
Answer: A
Explanation:
ERPS is a feature of ArubaOS-CX that prevents loops at layer 2 on ring networks1. ERPS uses a protocol called Ring Auto Protection Switching (RAPS) to detect link failures and perform fast traffic switchover1. ERPS has two timers that control the protection switching mechanism: guard timer and hold off timer1. The guard timer prevents false switching caused by delayed or lost RAPS PDUs1. The hold off timer causes ERPS switches to delay unblocking a failed link after the link is restored1. This can be useful to prevent frequent topology changes due to link flapping or network instability1. Therefore, this is a guideline for configuring timers for ERPS, and the correct answer is yes. For more information on ERPS and timers, refer to the Aruba Data Center Network Specialist (ADCNS) certification datasheet2 and the ERPS Guide for your switch model1.
NEW QUESTION # 27
A customer's servers use ISCSI, and they send data and storage traffic on the same pair of I OGbE links. Is this a best practice for supporting the ISCSI requirements?
Solution: Use Virtual Routing and Forwarding (VRF) to tunnel iSCSI traffic through the network spine on the same links that data traffic uses.
- A. No
- B. Yes
Answer: A
Explanation:
ISCSI is a protocol that allows storage devices to communicate over IP networks. ISCSI traffic has different requirements than data traffic, such as low latency, high throughput, and reliability.
Therefore, it is not a best practice to send data and storage traffic on the same pair of 10GbE links, as this can cause congestion and performance degradation. It is also not a best practice to use Virtual Routing and Forwarding (VRF) to tunnel ISCSI traffic through the network spine on the same links that data traffic uses. VRF is a technology that creates multiple isolated Layer 3 domains on a physical network, each with its own routing table. VRF does not provide any benefits for ISCSI traffic, as it does not guarantee bandwidth, priority, or quality of service. VRF also adds overhead and complexity to the network configuration. Therefore, this is not a valid way to support the ISCSI requirements.
NEW QUESTION # 28
You are using NetEdit to manage AruDaOS-CX switches. You want to deploy a standard config to the switches, but need the config to include a few device-specific settings such as hostname and IP address.
Is this what you should do?
Solution: Inside a configuration plan, right-click any device-specific parameters and modify the parameter per-device.
- A. Yes
- B. No
Answer: A
Explanation:
Inside a configuration plan, right-click any device-specific parameters and modify the parameter per-device is what you should do if you want to use NetEdit to manage ArubaOS-CX switches and deploy a standard config to the switches, but need the config to include a few device-specific settings such as hostname and IP address. This approach allows you to edit any parameter value for individual devices within a configuration plan without affecting other devices or creating separate plans1.
NEW QUESTION # 29
Is this part of a valid strategy for load sharing traffic across the links in an Ethernet Ring Protection Switching (ERPS) solution?
Solution: Create two ERPS instances for the ring and assign different VLANs and different ring protection links (RPL) to each instance.
- A. Yes
- B. No
Answer: A
Explanation:
Creating two ERPS instances for the ring and assigning different VLANs and different RPLs to each instance is part of a valid strategy for load sharing traffic across the links in an ERPS solution1. ERPS is a protocol that provides protection and recovery for Ethernet traffic in a ring topology1. It uses a RPL to block one of the links in the ring and prevent loops1. By creating two ERPS instances with different RPLs, you can use both links in the ring for different VLANs and achieve load sharing1.
NEW QUESTION # 30
Is this a best practice when positioning ArubaOS-CX switches in data center networks?
Solution: Deploy Aruba CX 6300 switches as data center spine switches.
- A. No
- B. Yes
Answer: A
Explanation:
Deploy Aruba CX 6300 switches as data center spine switches is not a best practice when positioning ArubaOS-CX switches in data center networks. The Aruba CX 6300 switches are designed for data center leaf roles, and they provide high density, low latency, and advanced features such as VSX and EVPN. The Aruba CX 83xx switches are more suitable for data center spine roles, and they provide high performance, scalability, and resiliency.
NEW QUESTION # 31
Is this a way that a data center technology can help meet requirements for multi-tenancy?
Solution: Virtual Extensible LAN (VXLAN) enables multiple isolated Layer 3 domains, each with its own routing table, to share a physical network.
- A. No
- B. Yes
Answer: A
NEW QUESTION # 32
You are using NetEdit to manage AruDaOS-CX switches. You want to deploy a standard config to the switches, but need the config to include a few device-specific settings such as hostname and IP address.
Is this what you should do?
Solution: omit the device-specific settings from the configuration plan and include them in command scripts instead.
- A. No
- B. Yes
Answer: A
Explanation:
Omit the device-specific settings from the configuration plan and include them in command scripts instead is not what you should do if you want to use NetEdit to manage ArubaOS-CX switches and deploy a standard config to the switches, but need the config to include a few device-specific settings such as hostname and IP address. This approach would require you to create separate command scripts for each switch, which can be tedious and error-prone. A better approach would be to use an auto config plan that uses scripts to customize the configuration for each switch based on variables such as serial number, MAC address, or user-defined parameters.
NEW QUESTION # 33
Is this a rule for configuring schedule profiles on an ArubaOS-CX switch?
Solution: With the exception of a single strict priority queue, all queues must use the same scheduling algorithm.
- A. Yes
- B. No
Answer: A
Explanation:
With the exception of a single strict priority queue, all queues must use the same scheduling algorithm is a rule for configuring schedule profiles on an ArubaOS-CX switch. A schedule profile defines how traffic is scheduled across different queues on an interface. Each queue can have one of three scheduling algorithms: strict priority (SP), weighted round robin (WRR), or weighted fair queuing (WFQ). However, only one queue can have SP, and all other queues must have either WRR or WFQ.
NEW QUESTION # 34
Can you attach this type of ArubaOS-CX interface to a VRF?
Solution: A loopback interface
- A. No
- B. Yes
Answer: A
Explanation:
A loopback interface can be attached to a VRF on an ArubaOS-CX switch. A loopback interface is a virtual interface that has an IP address assigned to it and is always up. A loopback interface can be attached to a VRF by using the vrf attach command under its configuration mode1.
NEW QUESTION # 35
......
HP HPE2-W09 (Aruba Data Center Network Specialist) Certification Exam is a comprehensive test designed to assess the skills and knowledge of IT professionals in the field of data center networking. Aruba Data Center Network Specialist Exam certification is ideal for individuals who aspire to become experts in designing, implementing, and managing data center networks using Aruba technology.
HPE2-W09 Exam Dumps, HPE2-W09 Practice Test Questions: https://pass4sure.examcost.com/HPE2-W09-practice-exam.html
